|About |Site Map |

ZIVE SP5H  is ±40Volt version of ZIVE SP5.  System is designed under FPGA and DSP control with high speed capability with   DAC control: Two set of high speed 16 bit DAC(50MHz) for offset & scanning & one set                             of 16 bit DAC(1MHz) for auxiliary analog output control. ADC Reading: Two set of 16 bit 500kHz ADC for reading voltage/current and 4 channel                             16 bit 250kHz ADCs for auxiliary data input such as temperature,                             auxiliary voltage etc. It can provide high frequency EIS, fast pulse                             techniques with options and high speed sampling time.   ZIVE SP5H is equipped with a frequency response analyzer(FRA) for system as standard and it provides high performance impedance measurements over the frequency range 10uHz to 300kHz.  ZRA(zero resistance ammeter) function can measure max 1 A in galvanic corrosion technique. ZIVE SP5H can be easily upgraded with  adding optional application software package without returning the system to the factory for upgrade.    Versatility ZIVE SP5H's system comes with additional three analog inputs (auxiliary voltage input) and 1 analog output, whereas 3 digital outputs and 2 digital inputs and one temperature input for K type thermocouple. It will help user expand the usage of instrument. For example, 1. User can measure the voltage between working electrode and counter electrode and between counter electrode and reference electrode adding to measurement between working electrode and reference electrode using 2 additional analog inputs(auxiliary voltage inputs). 2. Using analog output, it can control rotating speed of rotator, MFC flow rate etc. by +/-10V full scale.   3.  User can control on/off of max 3 devices by DO etc.    Safety/Maintenance 1.  When communication failure between PC and ZIVE SP5H occurs, running channel will continue the experiments and save the data into ZIVE memory up to 542,000 data point set. When the communication is recovered, ZIVE will transfer saved data to PC. User can transfer data set from ZIVE to PC anytime. This function will be highly efficient for long time experiment.   2.  User can define safety condition setting by inputting his/her own safety levels for voltage, current, temperature etc. If the measurement value exceeds this setting value, the system will automatically stop to protect the system and cell.   3.  If control value of voltage or current is different from measured value, the experiment will be stop automatically to protect the cell.   4.  Automatic calibration function is supplied for user calibration.  The system is controlled from a PC via USB or an Ethernet connection(Future function).   Application ZIVE SP5H electrochemical workstation is ideal for  high voltage application such as corrosion/coatings, electrode material, evaluation power device research such as battery materials, fuel cells, super capacitors and solar cells. Software (SmartManager)   ZIVE SP5H electrochemical workstation use SmartManager software. You can get more detailed information via above link.   Specification Main system PC communication USB2.0 High Speed Line voltage 100-240VAC, 50/60Hz, 1Amp LED Run,Busy,Potentiostat,Galvanostat Size/weight 179 x 270 x 378.4(W*H*D) / 7.65kg Power consumption 40V@1A 40Watt ¡¡ ¡¡ System Cell cable 1meter shielded type (Standard) ¡¡ Power terminal: Working,  counter, ¡¡ Sensing terminal: Reference, Working sense Control DSP with FPGA Calibration Automatic Data acquisition 2x16bit ADCs (500kHz)for voltage, current ADC 4x 16bit ADCs(250kHz) for auxiliary voltage & temperature reading DAC 2x16bit DAC(50MHz) for bias & scan 1X16bit DAC(1MHz) for analog output Filter 4ea (5Hz,1kHz,500kHz, 5MHz) Scan rate 0 – 200V/sec in common mode 0-5000V/sec in fast mode Max. channel No. 32 Channels via USB connection Internal Data Memory 542,000 points LCD Display DC & EIS mode automatically ¡¡ ¡¡ Power amplifier(CE) Power 40Watt (40V@1A) Compliance voltage ±40V Maximum current ±1A Control speed selection 8ea bandwidth 1MHz Slew rate 10V/usec ¡¡ ¡¡ Potentiostat mode(voltage control) - voltage control Control voltage range ±40V, ±4V, ±400mV Voltage resolution 16 bit per each range Voltage accuracy ±4mV±0.1% of setting Max. scan range ±40V vs. ref. E - current measurement Current ranges 11 ranges(auto/manual setting) 100pA ~ 1A ( 100pA with gain) Current resolution 16 bit; 30uA, 3uA, 300nA, 30nA, 300pA,, 30pA, 3pA, 300fA, 30fA, 3fA, Current accuracy ±0.2% of range ¡¡ ¡¡ Galvanostat mode(current control) - Current control Control current range Max. ±1A ± full scale depending on selected range Current resolution 16 bit; 30uA, 3uA, 300nA, 30nA, 300pA,, 30pA, 3pA, 300fA, 30fA, 3fA ¡¡ Current accuracy ±0.2% of range - Voltage measurement Voltage ranges 40V,4V,400mV Voltage resolution 16 bit; 1.2mV,120uV,12uV Voltage accuracy ±4mV±0.1% of reading Electrometer Max input voltage ±40V Input Impedance 2x10^13Ohm|1pF CMRR >95db ¡¡ ¡¡ EIS(Internal FRA) for system Frequency range 10uHz ~ 600kHz Frequency accuracy <0.01% Frequency resolution 5000/decade Amplitude 1mV ~ 20V rms (Potentiostatic) 0.1 ~ 70% f.s(Galvanostatic) Mode Static EIS: Potentiostatic, galvanostatic, pseudo-galvanostatic, OCP Dynamic EIS: Potentiodynamic, Galvanodynamic Fixed frequency Impedance: Potentiostatic, Galvanostatic, potentiodynamic, galvanodynamic Multisine EIS: Potentiostatic, Galvanostatic ¡¡ ¡¡ ¡¡ Interfaces  for system¡¡ Auxiliary port ¡¡  Digital output 3 (open collector)  Digital input 2 (photo coupler)  Auxiliary voltage inputs 3 analog Inputs: ±10V ¡¡ For measurement of WE vs. CE ¡¡ CE vs. RE or other signal  Analog output 1 analog output: ±10V ¡¡ For stirrer, MFC, RDE etc. Misc.  port ¡¡ Sig generator output 1 analog output for FRA output or  waveform generation output Peripheral communication I2C to control external devices ¡¡ ¡¡ Temperature measurement 1 K-type thermocouple input Zero Resistance Ammeter 1nA ~ 1A ranges ¡¡ ¡¡ Software¡¡ Max steps per experiment 1000 Shutdown safety limits Voltage, current, temperature etc Max. sampling rate 20kHz(50usec)-burst mode | 500kHz(2 or 3usec)-fast scan mode Max. sampling time unlimited Sampling condition Time, dv/dt, dI/dt, temp etc. PC requirement ¡¡ Operating system WindowsXP/2000/Vista/7/8 PC specification(minimum) Pentium4, RAM 1GB Display 1600x900 high color USB High speed 2.0 General¡¡ Dummy cell One external dummy cell included Thermocouple 1.5meter K-type (option) Auxiliary cable Option Misc. cable Option Specifications & software subject to change without notice.      ZIVELAB Windows is a registered trade mark of Microsoft Corporation.

© 2011  ZIVE LAB | support@wonatech.com